RE: no voice heard over the line channel ch=ipmB1C1 ErrorCode=0x5a04 -Out of...
How are you opening the GC line device handle in this case? Are you creating a full duplex route between the GC and voice devices? Make sure you also have correct IP address selected in the CLI...
View ArticleRE: Dialogic JCT Series Board Install Problems
You mentioned prior the boards are showing in windows device manager even as questions marked next to them as unknown devices? If that is the case, then maybe some type HW issue. What physical server...
View ArticleRE: Dialogic JCT Series Board Install Problems
Hello,the boards have never shown under windows device manager,the server is HP Proliant ML350, Gen9, and seems to have the latest BIOS (p92, v2.30)thanks.
View ArticleRE: Dialogic JCT Series Board Install Problems
What PCI-E X factor are the slots of which the boards are sitting in this case? Jeff
View ArticleRE: Dialogic JCT Series Board Install Problems
x16, also tried the others with correct power settings - none worked. thanks.
View ArticleRE: Dialogic JCT Series Board Install Problems
Ok, sounds like some type of HW inter-op issue in this case. It would not be the first time that HP has made changes to their BIOS that broke back compatibility with older PCI-e boards.This was last...
View ArticleRE: Dialogic HMP and Hyper-V
It is my understanding that HMP on virtual machines - is only supported on VMware ESXi
View ArticleRE: no voice heard over the line channel ch=ipmB1C1 ErrorCode=0x5a04 -Out of...
Hi Jeff,We are using the same program. Our old server installed InxHMP_4.1_161 and the voice works fine. Now we installed the latest version of InxHMP_4.1_213 and it failed to play the voice. Every...
View ArticleRE: no voice heard over the line channel ch=ipmB1C1 ErrorCode=0x5a04 -Out of...
Hi,Did you recompile the application on the new build? I know there were a lot of changes internal components and such and it always recommended to recompile with that big of a jump in builds. Jeff
View ArticleRE: Dialogic HMP and Hyper-V
While the above statement about only supporting VMware is true, there must be some other difference here which is inducing the issue at the remote site. With respect to the issue, is the HMP and HPET...
View ArticleRE: Dialogic HMP and Hyper-V
The HMP device states that it is working properly. The HPET driver states that it cannot find enough free resources that it can use (Code 12). I have tried both SU 367 and 372. The log shows:...
View ArticleRE: Number of Channels
Hi, The answer to the first question is complete dependent on the specific product of which you are using. Is this for System Release, or HMP baseline?Pending that answer you would review the...
View ArticleRE: Number of Channels
Jeff,I'm using D4PCI card with SR6 for relatively simple voice application (receive and make calls, detect tones, paly audio, record audio).I found the brd_GetAllPhysicalBoards() to detect system...
View ArticleDialogic HMP and Hyper-V
I am having issues getting the DM3 virtual board to be recognized on 2 different Hyper-V VM's that I am working on. The Hyper-V machines are off site so I am loading the software remotely. I have built...
View ArticleRE: Dialogic HMP and Hyper-V
Jeff,It will load on a Gen. 1 Hyper-V machine, but not on a Gen. 2. Thanks for the help.Mark
View ArticleRE: no voice heard over the line channel ch=ipmB1C1 ErrorCode=0x5a04 -Out of...
Hi Jeff,We did a recompile of the application with the same HMP4.1 build but the problem persist. Last time we tried a reboot and reactivate one of the license and it fixed the issue. However, the...
View ArticleRE: no voice heard over the line channel ch=ipmB1C1 ErrorCode=0x5a04 -Out of...
Refer to section 1.76 support for additive licenses in HMP 4.1 Linux release update notes:www.dialogic.com/.../release_update.pdfYou can use a conf command as noted to enable all licenses in a certain...
View ArticleNumber of Channels
Hello,I'm relatively new to the Dialogic cards and have few questions:1. How do I find out the number of channels on a detected board ? iterate with dx_open ?2. Can anyone recommend a good review...
View ArticleRE: Number of Channels
Hi,In this case it might be best to call sr_getbroardcnt since you only have a 4 port board in this case. Refer to the SRL Library reference in that case:www.dialogic.com/.../srl_api_v6.pdfJeff
View Article